Hyundai Genesis Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 26 Results
  1. The HOWTO or FIX Forum
    Disclaimer: I'm not responsible for any damage you may cause to your vehicle or any injury to your person from attempting this mod as it is only a guideline to DIY & you work at your own risk. I gave this DIY a 2 out 5 difficulty, but since I had to trim one of the gold 7/16 bolts by 1/2" &...
  2. The HOWTO or FIX Forum
    Disclaimer: I'm not responsible for any damage to your vehicle or any injury to your person while attempting this procedure as it is only a guideline. Tools needed: 10mm socket & ratchet (preferrably impact) & phillips screw driver (preferrably cordless). First remove the snorkel air intake by...
  3. The HOWTO or FIX Forum
    Disclaimer: I'm not responsible for any damage caused to your vehicle or any injury you may incur from doing this as it is only a guideline to follow. I give this a 1 out 5 difficulty. You have to remove the front bumper to install this grille properly, but removing the bumper on the GenCoupe...
  4. The HOWTO or FIX Forum
    Disclaimer: As always, I hold no responsibility for damage to your vehicle or injury to your person while attempting this modification. I give this a 2 out of 5 difficulty with the only hard part being having enough balls to splice into your OEM wiring harness. The ability to properly solder &...
  5. The HOWTO or FIX Forum
    I decided to move my Aeorforce Interceptor scan guage over to the left of the instrument cluster near the tripometer & furtherest left A/C vent after seeing another member on the other site's pics of thiers located there. I'm doing this purely for asthetic reasons as I belive the prior location...
  6. The HOWTO or FIX Forum
    Disclosure: Work at own risk as this is only a guide for this project & I'm not responsible for any damage done to your vehicle or any injuries you may incur. I give this project a 2 out of 5 difficulty. It is a little tedious & you have to take your time so you don't mangle your bumper cover...
  7. The HOWTO or FIX Forum
    Disclaimer: I hold no responsibility for any damage to your vehicle or injury to your person from the work you are going to perform in this DIY, so work at your own risk & these instructions are only a guide line. Tools needed: stubby phillips screwdriver, long phillips screwdriver, wire...
  8. The HOWTO or FIX Forum
    I decided to do this mod as the result of the driver's side fender liner being ripped out of the front bumper & breaking off about 1/3 the way up toward the left front strut. This occured during an incident where I went off track into the grass at CMP last time I was there. I removed both...
  9. The HOWTO or FIX Forum
    This is a DIY (do it yourself) & therefore I claim no responsibility for injury or damage to your car while doing this mod as this is only a guideline. Hyundai designed a front bumper IMO that looks just fine. Its the way they trimmed it out that looks like shit. I even like the way the bumper...
  10. The HOWTO or FIX Forum
    I didn't know what forum to put this in, so decided do it yourself fit best. I need a lightweight low clearance aluminum floor jack to take in the back of my car with me to the track. Since we have many establised racers/vendors on this site, I was hoping someone could give me a lead on the...
  11. The HOWTO or FIX Forum
    Disclaimer: This is just my recommended process for replacing brake lines & therefore is not the rule. In addition, I am no technician or hold any technical credits at any school in any form. Work at own risk & spend the extra time to take safety measures when lifiting your vehilcle. Needed...
  12. The HOWTO or FIX Forum
    I retrieved this from gencoupe & want to thank JohnPawlak for the OP. "Some of you have already done this, but for those that are thinking about and haven't done it yet, this might help. I've got lots of nice pics, but the post counter won't let me post them yet. I'll edit it later when my post...
  13. The HOWTO or FIX Forum
    retrieved from gencoupe, OP HGCOwner This how to will illustrate the steps needed to install the LED Kit from Diode Dynamics without breaking anything. BTW the stage 3 is ridiculously bright, the dome lights are actually a little TOO bright. Step 1) License plate bulbs Push the clip in and...
  14. The HOWTO or FIX Forum
    retrieved from gencoupe, OP dogstar It was a busy afternoon, I managed to get the passenger door panel off and take some measurements. Italyn, things look good for getting a reasonably shallow 8" mid woofer in there. The stock speaker is a plastic bodied speaker of approximately 6" diameter...
  15. The HOWTO or FIX Forum
    retrieved from gencoupe OP hkerekes "I spent a few hours installing my V1 and remote mount today. It was fairly easy and all i have left is to figure out a spot / way to mount the remote display. First open the sun glass holder door and take the two Phillips head screws out from the opening...
  16. The HOWTO or FIX Forum
    Retrieved from gencoupe OP ScoobahSt3ve even though I disagree with running HIDs w/o the proper ballasts, levelers & housings, there will still be those that are going to do it, so here's the DIY. "Here is the how to. its my first one so any suggestions to make it better would be nice. I also...
  17. The HOWTO or FIX Forum
    Retrieved from gencoupe thanks to OP Sonic Genesis "Ok, so I couldn't sleep tonight so I decided to keep myself occupied by a project. Here is the step by step on how to give your Gen some black housing headlights: Step One: -Remove headlights by unbolting the two 10mm bolts per side. -Un-clip...
  18. The HOWTO or FIX Forum
    Retrieved this from gencoupe originally posted by ImportShark "In order to install the Sequence foglight bezels, you'll first need to remove your front bumper. See my Front Bumper Removal DIY for instructions on that. Once the bumper is off, here's how to install the Sequence foglight setup...
  19. The HOWTO or FIX Forum
    Retrieved this from gencoupe originally posted by ImportShark "Here's a step-by-step guide to removing your front bumper. This is a useful DIY because it is applicable to removing your OEM front grill (to install aftermarket grills or install wing emblems), installing OEM foglights, installing...
  20. The HOWTO or FIX Forum
    "ok guys, so I finally got around removing my bumper to do some anti-rust for the components behind it. So hopefully this will shed some light on all those people that wanted to know how to remove it either for changing the grill or doing some repair. As the HMAservice.com indicates you need...
1-20 of 26 Results
Top